21.09.2019

DShK machine gun: characteristics. Large-caliber machine gun DShK. Large-caliber machine guns DShK and DShKM 12.7 mm anti-aircraft machine gun DShK in the Navy

Caliber: 12.7×108 mm
Weight: 34 kg machine gun body, 157 kg on a wheeled machine
Length: 1625 mm
Barrel length: 1070 mm
Nutrition: 50 round belt
Rate of fire: 600 rounds/min

The task to create the first Soviet heavy machine gun, intended primarily to combat aircraft at altitudes of up to 1500 meters, was issued by that time to the already very experienced and well-known gunsmith Degtyarev in 1929. Less than a year later, Degtyarev presented his 12.7mm machine gun for testing, and in 1932, small-scale production of the machine gun began under the designation DK (Degtyarev, Large-caliber). In general, the DK was similar in design to the DP-27 light machine gun, and was powered by detachable drum magazines for 30 rounds, mounted on top of the machine gun. The disadvantages of such a power supply (bulky and heavy magazines, low practical rate of fire) forced the production of the recreational weapon to cease in 1935 and to begin its improvement. By 1938, designer Shpagin developed a belt feed module for the recreation center, and in 1939 the improved machine gun was adopted by the Red Army under the designation “12.7mm heavy machine gun Degtyarev-Shpagin model 1938 - DShK.” Mass production of DShK began in 1940-41. They were used as anti-aircraft weapons, as infantry support weapons, and installed on armored vehicles and small ships (including - torpedo boats). Based on the experience of the war, in 1946 the machine gun was modernized (the design of the belt feed unit and barrel mount were changed), and the machine gun was adopted under the designation DShKM.
The DShKM has been or is in service with over 40 armies around the world and is produced in China (“type 54”), Pakistan, Iran and some other countries. The DShKM machine gun was used as an anti-aircraft gun on Soviet tanks of the post-war period (T-55, T-62) and on armored vehicles (BTR-155). Currently, in the Russian Armed Forces, the DShK and DShKM machine guns have been almost completely replaced by the Utes and Kord large-caliber machine guns, which are more advanced and modern.

The DShK heavy machine gun is an automatic weapon built on the gas exhaust principle. The barrel is locked by two combat larvae, hinged on the bolt, by recesses in the side walls receiver. The fire mode is automatic only, the barrel is non-removable, finned for better cooling, and equipped with a muzzle brake. The feed is carried out from a non-scattered metal tape; the tape is fed from the left side of the machine gun. In DShK, the tape feeder was made in the form of a drum with six open chambers. As the drum rotated, it fed the tape and at the same time removed the cartridges from it (the tape had open links). After the chamber of the drum with the cartridge arrived in the lower position, the cartridge was fed into the chamber by the bolt. The tape feeder was driven using a lever located on the right side, which swung in a vertical plane when its lower part was acted upon by the loading handle, rigidly connected to the bolt frame. In the DShKM machine gun, the drum mechanism has been replaced with a more compact slider mechanism, also driven by a similar lever connected to the charging handle. The cartridge was removed from the belt downwards and then fed directly into the chamber.
Spring buffers of the bolt and bolt frame are mounted in the buttplate of the receiver. The fire was fired from the rear sear (from the open bolt), two handles on the butt plate and evaporated triggers were used to control the fire. The sight was framed; the machine also had mounts for an anti-aircraft foreshortening sight.

The machine gun was used from a universal machine gun of the Kolesnikov system. The machine was equipped with removable wheels and a steel shield, and when using the machine gun as an anti-aircraft wheel, the shield was removed and the rear support was spread apart to form a tripod. In addition, the anti-aircraft machine gun was equipped with special shoulder rests. The main disadvantage of this machine was its high weight, which limited the mobility of the machine gun. In addition to the machine gun, the machine gun was used in turret installations, on remote-controlled anti-aircraft installations, and on ship pedestal installations.

DShK (GRAU Index - 56-P-542) - heavy-caliber machine gun chambered for 12.7×108 mm. Developed based on the design of the large-caliber heavy machine gun DK. In February 1939, the DShK was adopted by the Red Army under the designation “12.7 mm Degtyarev-Shpagin heavy machine gun, model 1938.”

DShK machine gun - video

With the start of work on a machine gun with a caliber of 12-20 millimeters in 1925, they decided to create it based on light machine gun magazine-fed to reduce the mass of the machine gun being created. Work began at the design bureau of the Tula Arms Plant on the basis of the 12.7-mm Vickers cartridge and on the basis of the German Dreyse (P-5) machine gun. The design bureau of the Kovrov plant was developing a machine gun based on the Degtyarev light machine gun for more powerful cartridges. A new 12.7-mm cartridge with an armor-piercing bullet was created in 1930, and at the end of the year the first experimental large-caliber Degtyarev machine gun with a Kladov disc magazine with a capacity of 30 rounds was assembled. In February 1931, after testing, preference was given to the DK (“Degtyarev large-caliber”) as easier to manufacture and lighter. The recreation center was put into service; in 1932, a small series was produced at the plant named after. Kirkizha (Kovrov), however, in 1933 only 12 machine guns were produced.

Military tests did not live up to expectations. In 1935, production of the Degtyarev heavy machine gun was stopped. By this time, a version of the DAK-32 had been created that had a Shpagin receiver, but tests in 1932-1933 showed the need to refine the system. Shpagin remade his version in 1937. A drum feed mechanism was created that did not require significant changes to the machine gun system. The belt-fed machine gun passed field tests on December 17, 1938. On February 26 of the following year, by resolution of the Defense Committee, it was adopted under the designation “12.7 mm heavy machine gun arr. 1938 DShK (Degtyarev-Shpagina large-caliber)" which was installed on universal machine Kolesnikova. Work was also carried out on the DShK aircraft installation, but it soon became clear that a special large-caliber was needed aircraft machine gun.

The automatic operation of the machine gun was carried out due to the removal of powder gases. A closed gas chamber was located under the barrel and was equipped with a pipe regulator. The barrel had fins along its entire length. The muzzle was equipped with a single-chamber active-type muzzle brake. By moving the bolt lugs to the sides, the barrel bore was locked. The ejector and reflector were assembled in the gate. A pair of spring shock absorbers of the butt plate served to soften the impact of the moving system and give it an initial rolling impulse. A return spring, mounted on the gas piston rod, activated the impact mechanism. The trigger lever was blocked by a safety lever mounted on the buttplate (setting the safety to the front position).

Feeding – belt, feeding – from the left side. The loose tape, which has semi-closed links, was placed in a special metal box attached to the left side of the machine bracket. The bolt carrier handle activated the DShK drum receiver: while moving backward, the handle bumped into the fork of the swinging feed lever and turned it. A pawl located at the other end of the lever rotated the drum 60 degrees, and the drum, in turn, pulled the tape. There were four cartridges in the drum at a time. As the drum rotated, the cartridge was gradually squeezed out of the belt link and fed into the receiving window of the receiver. The shutter moving forward caught it.

The folding frame sight, used for firing at ground targets, had a notch of up to 3.5 thousand m in increments of 100 m. The machine gun's markings included the manufacturer's mark, year of manufacture, serial number (series designation - two-letter, serial number of the machine gun) . The mark was placed in front of the butt plate on top of the receiver.

During operation with the DShK, three types of anti-aircraft sights were used. The ring remote sight of the 1938 model was intended to destroy air targets flying at speeds of up to 500 km/h and at a distance of up to 2.4 thousand meters. The 1941 model sight was simplified, the range was reduced to 1.8 thousand meters, however possible speed the target being destroyed increased (along the “imaginary” ring it could be 625 kilometers per hour). The sight of the 1943 model was of the foreshortening type and was much easier to use, but allowed firing at various target courses, including pitching or diving.

The universal Kolesnikov machine of the 1938 model was equipped with its own charging handle, had a removable shoulder pad, a cartridge box bracket, and a rod-type vertical aiming mechanism. Fire at ground targets was carried out from a wheeled vehicle, with the legs folded. To fire at air targets, the wheel drive was separated, and the machine was laid out in the form of a tripod.

The 12.7 mm cartridge could have an armor-piercing bullet (B-30) of the 1930 model, an armor-piercing incendiary bullet (B-32) of the 1932 model, sighting and incendiary (PZ), tracer (T), sighting (P), against anti-aircraft guns targets, an armor-piercing incendiary tracer bullet (BZT) of the 1941 model was used. The armor penetration of the B-32 bullet was 20 millimeters normal from 100 meters and 15 millimeters from 500 meters. The BS-41 bullet, whose core was made of tungsten carbide, was capable of penetrating 20 mm armor plate at an angle of 20 degrees from a range of 750 meters. The dispersion diameter when firing at ground targets was 200 millimeters at a distance of 100 meters.

The machine gun began to enter service with the troops in 1940. In total, in 1940, plant No. 2 in Kovrov produced 566 DShKs. In the first half of 1941 - 234 machine guns (in total, in 1941, with a plan of 4 thousand DShK, about 1.6 thousand were received). In total, as of June 22, 1941, the Red Army units had about 2.2 thousand heavy machine guns.

From the first days of the Second World War, the DShK machine gun proved itself to be an excellent anti-aircraft weapon. So, for example, on July 14, 1941, on the Western Front in the Yartsevo area, a platoon of three machine guns shot down three German bombers; in August, near Leningrad in the Krasnogvardeisky area, the Second Anti-Aircraft Machine Gun Battalion destroyed 33 enemy aircraft. However, the number of 12.7-mm machine gun mounts was clearly not enough, especially considering the enemy's significant air superiority. As of September 10, 1941, there were 394 of them: in the Oryol zone air defense– 9, Kharkov – 66, Moscow – 112, on the South-Western Front – 72, Southern – 58, North-Western – 37, Western – 27, Karelian – 13.

Since June 1942, the staff of the anti-aircraft artillery regiment of the army included a DShK company, which was armed with 8 machine guns, and since February 1943 their number increased to 16 units. The anti-aircraft artillery divisions of the RVGK (Zenad), formed since November 42, included one such company per anti-aircraft small-caliber artillery regiment. Since the spring of 1943, the number of DShKs in Zenad decreased to 52 units, and according to the updated state of the 44th in the spring, Zenad had 48 DShKs and 88 guns. In 1943, small-caliber regiments were introduced into the cavalry, mechanized and tank corps anti-aircraft artillery(16 DShK and 16 guns).

American infantrymen fire from a DShKM on a Romanian URO VAMTAC during joint US-Romanian maneuvers, 2009

Usually anti-aircraft DShK used by platoons, often included in medium-caliber anti-aircraft batteries, using them to provide cover from air attacks from low altitudes. Anti-aircraft machine gun companies, armed with 18 DShKs, were added to the staff of rifle divisions at the beginning of 1944. Throughout the war, losses of heavy machine guns amounted to about 10 thousand units, that is, 21% of the resource. This was the smallest percentage of losses in the entire system. small arms, however, it is comparable to losses in anti-aircraft artillery. This already speaks about the role and place of heavy machine guns.

In 1941, as German troops approached Moscow, backup factories were identified in case Factory No. 2 stopped producing weapons. The production of DShK was carried out in the city of Kuibyshev, where 555 devices and machines were transferred from Kovrov. As a result, during the war, the main production took place in Kovrov, and “duplicate” production took place in Kuibyshev.

In addition to easel ones, they used self-propelled units with DShK - mainly M-1 pickups or GAZ-AA trucks with a DShK machine gun installed in the body in the anti-aircraft position on the machine. "Anti-aircraft" light tanks on the T-60 and T-70 chassis further prototypes no progress. The same fate befell the integrated installations (although it should be noted that the built-in 12.7-mm anti-aircraft installations were used to a limited extent - for example, they served in the air defense of Moscow). The failures of the installations were associated, first of all, with the power system, which did not allow changing the direction of feed of the tape. But the Red Army successfully used 12.7-mm American quad mounts of the M-17 type based on the M2NV Browning machine gun.

The “anti-tank” role of the DShK machine gun, which received the nickname “Dushka,” was insignificant. The machine gun was used to a limited extent against light armored vehicles. But the DShK became a tank weapon - it was the main armament of the T-40 (amphibious tank), BA-64D (light armored car), and in 1944 a 12.7-mm turret anti-aircraft gun was installed on heavy tank IS-2, and later on heavy self-propelled guns. Anti-aircraft armored trains were armed with DShK machine guns on tripods or stands (during the war, up to 200 armored trains operated in the air defense forces). A DShK with a shield and a folded machine could be dropped to partisans or landing forces in a UPD-MM parachute bag.

The fleet began receiving DShKs in 1940 (at the beginning of the Second World War there were 830 of them). During the war, industry transferred 4,018 DShKs to the fleet, and another 1,146 were transferred from the army. In the navy, anti-aircraft DShKs were installed on all types of ships, including mobilized fishing and transport ships. They were used on twin single pedestals, turrets, and turrets. Pedestal, rack and turret (coaxial) installations for DShK machine guns, adopted for service navy, developed by I.S. Leshchinsky, designer of plant No. 2. The pedestal installation allowed for all-round firing, vertical guidance angles ranged from -34 to +85 degrees. In 1939 A.I. Ivashutich, another Kovrov designer, developed a twin pedestal installation, and the later appeared DShKM-2 gave all-round fire. Vertical guidance angles ranged from -10 to +85 degrees. In 1945, the 2M-1 twin deck-mounted installation, which had a ring sight, was put into service. The DShKM-2B twin turret installation, created at TsKB-19 in 1943, and the ShB-K sight made it possible to conduct all-round fire at vertical guidance angles from -10 to +82 degrees.

For boats of various classes, open turret twin installations MSTU, MTU-2 and 2-UK were created with pointing angles from -10 to +85 degrees. The “naval” machine guns themselves differed from the base model. For example, in the turret version, a frame sight was not used (only a ring sight with a weather vane front sight was used), the bolt handle was lengthened, and the hook for the cartridge box was changed. The differences between machine guns for coaxial installations were the design of the butt plate with the frame handle and release lever, lack of sights, fire control.

The German army, which did not have a standard heavy machine gun, willingly used captured DShKs, which were designated MG.286(r).

At the end of the Second World War, Sokolov and Korov carried out a significant modernization of the DShK. The changes primarily affected the food system. In 1946, a modernized machine gun under the DShKM brand was put into service. The reliability of the system has increased - if on the DShK according to the specifications 0.8% of delays during firing were allowed, then on the DShKM this figure was already 0.36%. The DShKM machine gun has become one of the most widely used in the world.

It is difficult to overestimate the role of machine guns in the development of military affairs - having cut short millions of lives, they forever changed the face of war. But even experts did not immediately appreciate them, at first considering them as special weapons with a very narrow range of combat missions - for example, at the turn of the 19th - 20th centuries, machine guns were considered just one of the types of fortress artillery. However, already during Russo-Japanese War automatic fire proved its highest efficiency, and during the First World War, machine guns became one of the most important means of fire defeating the enemy in close combat; they were installed on tanks, combat aircraft and ships. Automatic weapons made a real revolution in military affairs: heavy machine-gun fire literally swept away the advancing troops, becoming one of the main causes of the “positional crisis”, radically changing not only tactics combat, but also the entire military strategy.

This book is the most complete and detailed encyclopedia of Russian, Soviet and Soviet machine gun weapons to date. Russian army from the end of the 19th century to the beginning of the 21st century, both domestic models and foreign ones - purchased and captured. Author, leading historian small arms, not only leads detailed descriptions the device and operation of easel, manual, single, large-caliber, tank and aircraft machine guns, but also talks about their combat use in all the wars that our country waged throughout the turbulent twentieth century.

The DShKM is in service with more than 40 armies around the world. In addition to the USSR, it was produced in Czechoslovakia (DSK vz.54), Romania, China (“Type 54” and the modernized “Type 59”), Pakistan (Chinese version), Iran, Iraq, Thailand. However, the Chinese were also embarrassed by the bulkiness of the DShKM, and to partially replace it they created the Type 77 and Type 85 machine guns chambered for the same cartridge. In Czechoslovakia, based on the DShKM, a quad M53 anti-aircraft gun was produced, which was also exported - for example, to Cuba.

12.7 mm Type 59 machine gun - Chinese copy of DShKM - in anti-aircraft firing position

Soviet, and more often Chinese-made DShKMs fought in Afghanistan and on the side of the dushmans. Major General A.A. Lyakhovsky recalled that the dushmans “used large-caliber machine guns, anti-aircraft mountain installations (ZGU), small-caliber Oerlikon anti-aircraft guns as air defense weapons, and since 1981 - portable anti-aircraft guns missile systems and DShK made in China.” 12.7-mm machine guns turned out to be dangerous opponents of the Soviet Mi-8 and Su-25, and were also used to fire at convoys and checkpoints from a long distance. In the report of the Head of the GUBP Ground Forces dated September 22, 1984, among the weapons captured from the rebels it was indicated: DShK for May - September 1983 - 98, for May - September 1984 - 146. Afghan government troops from January 1 to June 15, 1987, for example, destroyed 4 ZGU, 56 DShK rebels, captured 10 ZGU, 39 DShK, 33 other machine guns, losing 14 of their own ZGU, 4 DShK, 15 other machine guns. During the same period, Soviet troops destroyed 438 DShK and ZGU, captured 142 DShK and ZGU, 3 million 800 thousand units of ammunition for them; divisions special purpose destroyed 23 DShKs and 74,300 units of ammunition for them, captured 28 and 295,807 units, respectively.

Homemade installation of a DShKM machine gun on a Mitsubishi pickup truck. Cote d'Ivoire. Africa

Despite repeated attempts to replace them, the Soviet DShKM and the American M2NV "Browning" have been sharing primacy in the family of heavy machine guns (generally small) for half a century and are the most widely used in the world - in a number of countries they are used together. At the same time, the DShKM, being larger and heavier than the M2NV, noticeably surpasses it in fire power.

Order incomplete disassembly DShKM

Disconnect the guide tube from the barrel by pulling it towards the muzzle and turning it to the left until the tube stop comes out of the groove on the barrel.

Remove the butt plate pin and, using a hammer, separate the butt plate downwards, holding it with your hand.

Separate trigger, moving it back.

Using the reloading handle, pull the moving system back and remove them together with the guide tube, supporting the latter.

Separate the bolt with the firing pin from the bolt frame and the lugs from the bolt.

Knock out the ejector axis, reflector pins and striker, then separate these parts from the bolt.

Knock out the frame clutch axis and separate the bolt frame from the return mechanism.

Place the return mechanism vertically and, pressing on the guide tube, knock out the front axis of the coupling, then smoothly release the tube and separate it and the return spring from the rod.

Unscrew and unscrew the receiver axle nut, push the latter out of the receiver socket and remove the feed mechanism.

Unscrew and unscrew the barrel wedge nut, push the wedge to the left and separate the barrel from the receiver.

Reassemble in reverse order.

TACTICAL AND TECHNICAL CHARACTERISTICS OF DShK (MOD. 1938)

Cartridge - 12.7?108 DShK.

The weight of the machine gun without belt is 33.4 kg.

The weight of the machine gun with the belt on the machine (without shield) is 148 kg.

The length of the machine gun “body” is 1626 mm.

Barrel length - 1070 mm.

Barrel weight - 11.2 kg.

Number of grooves - 8.

Type of rifling - right-handed, rectangular.

The length of the rifled part of the barrel is 890 mm.

The mass of the moving system is 3.9 kg.

The initial bullet speed is 850–870 m/s.

Muzzle energy of the bullet - 18,785 - 19,679 J.

Rate of fire - 550–600 rounds/min.

Combat rate of fire - 80 - 125 rounds/min.

The length of the aiming line is 1110 mm.

Sighting range- 3500 m.

Effective firing range - 1800–2000 m.

The height of the fire zone is 1800 m.

The thickness of the armor penetrated is 15–16 mm at a range of 500 m.

The power supply system is a metal belt for 50 rounds.

The weight of the box with tape and cartridges is 11.0 kg.

Machine type - universal wheeled tripod.

Pointing angles: horizontal - ±60 /360° degrees.

vertical - ±27/+85°, –10° deg.

Calculation: 3–4 people.

Transit time from stowed position in combat for anti-aircraft shooting - 0.5 min.

The USSR created many types of weapons, which to this day are very popular all over the world. These include the DShK machine gun. It has been removed from service in our country, but dozens of other countries are actively using it. In my time soviet soldiers gave this machine gun the nickname “Dushka”, transforming its abbreviation into a peaceful one, good name. But in reality it was a formidable large-caliber machine gun that terrified enemies.

How it all began

At the end of 1925, it turned out that the Red Army was in dire need of a powerful heavy machine gun. The designers were given the task of developing such a weapon, and the caliber had to be chosen within the range of 12-20 millimeters. On a competitive basis and based on test results, the 12.7 mm caliber cartridge was chosen as the main one. But the army command was not too satisfied with the presented weapons, and therefore new prototypes were constantly tested.

So, at the beginning of 1931, two machine guns were tested at once: the “Dreyse system” and the “Degtyarev system”. The commission considered that the sample from Degtyarev deserved attention, since it was much lighter and easier to manufacture. The first attempt at serial production was made in 1932, but the following year only 12 machine guns could be assembled, and in 1934 the production of the DK was completely curtailed. Initially, the DShK machine gun did not cause much enthusiasm among the military.

What happened

But the thing is that the next tests in 1934 revealed one unpleasant feature of the new gun: it turned out that the machine gun was virtually useless to fight even relatively fast targets (especially airborne ones), since the rate of fire was extremely low, and the magazines offered by the manufacturer were so heavy and uncomfortable that even experienced fighters experienced many difficulties when handling them. In 1935, a decree was issued to completely stop all production of DC.

By the way, do you know what the DShK (machine gun) is called correctly? The decoding is simple: “Degtyarev-Shpagina large-caliber.” Wait, how did the famous Shpagin get here? After all, we are talking about Degtyarev? It's simple.

The position of the practically rejected gun was saved by the outstanding domestic gunsmith G.S. Shpagin, who in 1937 invented a belt feed mechanism, the installation of which did not require any serious alteration of old machine guns. In April of the following year, the new design was successfully tested at the factory, in the winter the sample passed tests with flying colors with honor, and in 1939 the DShK machine gun “officially” appeared.

Information about the technical device

Automation is standard, it works by removing waste powder gases. The gas chamber had three holes of different diameters: using a small regulator, it was possible to flexibly regulate the amount of gases that was transferred directly to the gas piston. On the barrel, along its entire length, there are “ribs” that serve for more uniform and intense heat dissipation.

An active muzzle brake is attached to the muzzle. At first its shape resembled a parachute, but later designers began to use a flat-shaped brake.

The bolt frame is the basis of all automation. The barrel bore was locked using lugs on the bolt, which were moved in different directions. A return spring is mounted on the gas piston rod. Spring shock absorbers in the butt plate not only significantly soften recoil, but also prevent rapid wear of the weapon. In addition, it is they who give the bolt frame initial speed return movement. This ingenious innovation was proposed by Shpagin: this way the designer increased the rate of fire.

Of course, after introducing this device into the design, it was necessary to equip the machine gun with a rebound damping device so that the frame would not “jump” in the extreme forward position.

Reloading and shooting

A handle for reloading the weapon is rigidly coupled to the bolt frame. The mechanism for direct reloading of the machine gun system also interacts with it, but if the machine gunner inserts the cartridge with the head of the cartridge case, he can do without it. Shooting is done from an open bolt.

It should be remembered that the DShK machine gun allows only automatic fire and is equipped with a non-automatic safety lever, the principle of operation of which is based on complete blocking of the trigger.

The bolt, approaching the breech of the barrel, stops completely, while the bolt frame itself continues to move forward. The thickened part of the firing pin cocks the bolt lugs, which fit into special recesses made in the wall of the receiver. Even after the barrel is locked, the bolt carrier continues to move forward, where its firing pin hits the firing pin. The shutter is unlocked using the bevels of the same frame when it moves backwards.

Ammunition supply mechanism

Power is supplied from the tape. It is metal, link. Served from the left side. The tape is placed in a metal container attached to the machine gun mount. A large-caliber DShK machine gun is equipped with a drum-type belt receiver, which operates from the bolt frame handle. As it moved backwards, the feed lever was activated and rotated.

A pawl was attached to its other end, which rotated the drum 60 degrees in one step. Accordingly, due to this mechanical energy, the cartridge strip was pulled. The cartridge was removed from it in a side position.

Note that domestic 12.7 mm ammunition has a very wide range of cartridge types that can be used to solve various combat missions.

Sights, shooting at different types of targets

For shooting at ground-based targets, a relatively simple, folding frame sight is used, marked up to a range of 3.5 thousand meters. The anti-aircraft ring sight was adopted for service in 1938. It allowed firing at flying enemy aircraft at a distance of up to 2400 meters, but the target speed should not exceed 500 km/h. In 1941, a significantly simplified sight was adopted.

If it was used, the firing range was reduced to 1800 meters, but the theoretical target could move at speeds of up to 625 km/h. In 1943 appeared new type a sight that made it possible to effectively hit enemy aircraft at any course of their movement, even in cases where the pilot performed a dive or pitch-up. This made it possible to effectively fight attack aircraft, who, as a rule, attacked from a low altitude.

Anti-aircraft variant

How did the anti-aircraft DShK perform? The machine gun turned out to be not so good as a weapon for combating air targets. It's all about an imperfect anti-aircraft machine, which often negated all the advantages of new types of sights.

In particular, it turned out to be insufficiently stable. A limited series of special anti-aircraft machines with convenient bipods and additional sights, but they (due to the difficulties of the war years) never went into production.

Special, balanced anti-aircraft installations were also developed. For example, the DShK coaxial machine gun was quite popular. Difficulties with their serial production were associated with the power supply system: without subjecting the weapon to significant alterations, it was impossible to move the tape receiver to the other side. In the case of using built-in installations, all this created serious difficulties for the gun crew.

Production and combat use

The machine guns went into production in 1939. They began to enter the army and navy starting next year. At first, there was a chronic lag between the plan and reality: for example, in 1940, the production of 900 units was planned, while the plant was only able to produce 566 units.

In the first six months of 1941, only 234 DShKs were produced, although at least four thousand units had to be made in just a year. It is not surprising that the army and navy constantly, throughout the war, experienced a chronic shortage of heavy machine guns. Since the need for this type of weapon was greater at sea, 1,146 DShKs were transferred from the army to sailors throughout the war.

However, the situation improved relatively quickly: in 1942 the army already received 7,400 machine guns, and in 1943 and 1944 almost 15 thousand DShKs were produced annually.

What were they used for?

Since there were few machine guns, they became the main type of anti-aircraft weapon: they were not used so often to combat ground targets. However, in the first year of the war, the Wehrmacht constantly threw light tanks and wedges into battle, against which the DShK was a formidable weapon, and therefore machine guns were “requisitioned” from anti-aircraft units.

Later, these weapons began to be transferred to anti-tank units as a matter of routine, as fighters used them to fight off attacks from enemy attack aircraft.

In urban battles, the DShK turned out to be much more in demand specifically for combating enemy personnel. It often happened that it was very difficult to “pick out” Germans from a simple brick house (due to the lack of grenade launchers at that time). But if the assault group was armed with a DShK machine gun, the caliber of which made it possible not to pay special attention to the walls, then the situation changed dramatically for the better.

In service with tankers

Often the machine gun was mounted on domestic tanks. In addition, they installed it on the Soviet armored car BA-64D. A full-fledged turret with a DShK appeared in 1944, with the adoption of the IS-2 heavy tank. In addition, self-propelled guns were often equipped with machine guns, and this was often done by the crew themselves.

It is important to note that there was an acute shortage of domestic machine guns of this system during the war years. In the United States, over the same period, more than 400 thousand units of Browning M2HB alone were produced. It is not surprising that when planning deliveries under Lend-Lease, special attention was paid to heavy machine guns.

Basic performance characteristics

What else characterizes the DShK machine gun? Its characteristics were as follows:

Cartridge - 12.7x108 mm (domestic variation of the same "Browning").
The body of the machine gun weighed 33.4 kg (without tape and cartridges).
With the machine (modification without a shield) the weight was 148 kg.
The total length of the weapon is 1626 mm.
The barrel length was 1070 mm.
Theoretical rate of fire is 550-600 rounds per minute.
The rate of fire in combat conditions is 80-125 rounds per minute.
The theoretically possible firing range is 3500 meters.
The actual range is 1800-2000 meters.
The thickness of the armor steel to be penetrated is up to 16 mm at a distance of 500 meters.
Food - link belt, 50 rounds per piece.

These are the characteristics of the DShK (machine gun). Its performance characteristics are such that this weapon is still used in dozens of countries around the world, and various modifications are still produced.

DShK(Dektyarev-Shpagin Large-caliber) - Soviet 12.7-mm machine gun developed by designers Degtyarev and Shpagin. In February 1939, the DShK was adopted by the Red Army under the designation “12.7 mm heavy machine gun DShK model 1938.” Mass production of DShK began in 1940-41. The cartridge used is 12.7x108 mm DShK. Ammunition was supplied from a box with a belt for 50 rounds, fed from the left. The machine gun has a fairly high rate of fire, which makes fire effective against fast-moving targets.

Based on war experience, the machine gun was modernized (the design of the tape feed unit and barrel mount were changed), and in 1946 it was put into service Soviet army under the designation DShKM. Various sights could be attached to the machine gun: frame, ring, collimator, as well as various flame arresters and muzzle brakes. The machine gun was or is in service with over 40 armies around the world, and is still used in many conflicts around the world. Currently, in the Russian army, DShK and DShKM machine guns have been almost completely replaced heavy machine guns“Cliff” and “Kord”, more advanced and modern.

Cartridge 12.7Х108 in comparison with other cartridges (from left to right: 5.45Х39, 7.62Х39, 7.62Х54)

Cartridge 12.7X108 in comparison with other large-caliber cartridges

DShK model 1938

Vehicles equipped with these weapons

IS-2 (1944), IS-3, IS-4M
ISU-122, ISU-122S, ISU-152
T-54 (1947), T-54 (1951), T-55A, T-44-100, Type 62 (USSR)

Main characteristics

Composition of tapes

The cartridges used in the DShK are: BZ - armor-piercing incendiary, T - tracer, MDZ - instant-action incendiary, BZT - armor-piercing incendiary tracer, BZ(MKS) - armor-piercing incendiary with a metal-ceramic core.

Purpose and features different types bullets in the game: Aviation ammunition

Belts for ZSU GAZ DShK

Ribbon	Compound
Standard	BZ-T-MDZ
BZ	BZ(ISS)-BZT-BZ(ISS)-BZT
B	BZ(ISS)-BZ(ISS)-BZT
BZT	BZT-BZT-BZ(ISS)

Standard tape (for turret and coaxial DShK machine guns on tanks and self-propelled guns) - composition: BZT-MDZ-BZT-BZ(MKS)

DShKM model 1945

Anti-aircraft installation in the back of a truck (three 12.7-mm DShK machine guns) in the center of Moscow, on Sverdlov Square (now Teatralnaya). The Metropol Hotel is visible in the background.

Comparison with analogues

The widespread American Browning M2 (12.7 mm) machine gun can be compared with the DShK machine gun. The M2 is inferior in penetration (since it does not have cartridges with a metal-ceramic core, like the DShK), in rate of fire, and muzzle energy of the bullet. However, the M2 is superior in the number of cartridges in the box (minimum 100, maximum 200 for the ZSU), the barrel is longer, and penetration by BZ and BZT cartridges is a couple of millimeters higher. They are the same in terms of reload speed.
The French machine gun Hotchkiss Mle.1930 is inferior to the DShK in rate of fire (450 rpm), penetration, number of loaded cartridges (30 in a box magazine). But Hotchkiss is superior to the DShK in reload speed and caliber (13.2 mm).

Use in combat

The DShK machine gun perfectly penetrates with BZ (MKS) cartridges, but you should remember that the 50-round cartridge box is quickly running out. Lightly armored vehicles are vulnerable to DShK cartridges (ZSU, light-medium tanks and self-propelled guns), but it is advisable to study them as well weak spots(for example sides, stern, trunk). Bullets from a machine gun can also be used to point at the enemy to allies and prevent the enemy from seeing. Against aircraft, it makes sense to use an MDZ cartridge (explosive, with explosives inside).

Advantages and disadvantages

The DShK machine gun (12.7 mm) is quite good in the game; it allows you to fight both lightly armored vehicles and aircraft. It has good armor penetration and rate of fire. Although the machine gun is not without its shortcomings compared to other analogues.

Advantages:

Good rate of fire.
The 12.7 mm machine gun is capable of fighting not only unarmored vehicles and aircraft, but also lightly armored vehicles.
An excellent penetrating and at the same time incendiary cartridge with a metal-ceramic core BZ (MKS).
Explosive cartridges MDZ.

Flaws:

Long reload (10.4 sec).
Small usable belt (50 rounds)

Historical reference

SHVAK 12.7 mm

12.7-mm ShVAK machine gun on an anti-aircraft rack of Ershov, Ivanov, Chernyshev in the back of a GAZ-AA truck

Aviation DNA: synchronous-wing

Wing DShKA 1938

Vasily Alekseevich Degtyarev (1879/1880 - 1949) - Russian and Soviet designer small arms. Hero of Socialist Labor. Winner of four Stalin Prizes.

Georgy Semyonovich Shpagin (1897-1952) - Soviet designer of small arms. Hero of Socialist Labor (1945). Recipient of 3 Orders of Lenin.

The task to create the first Soviet heavy machine gun was issued to the experienced and well-known gunsmith Degtyarev in 1929. Less than a year later, he presented his 12.7 mm machine gun for testing, and in 1932, small-scale production of the machine gun under the designation DK began. Military tests of the DK and additional field tests in 1934 showed that the machine gun was of little use for combating fast-moving targets due to its low rate of fire. Although the rate of fire reached a quite acceptable 360-400 rounds/min, the practical rate of fire did not exceed 200 rounds/min, which was due to the heavy and bulky magazines. We experimented with different machines and different box magazines, but they had even less capacity. The DAK-32, intended for both fixed wing installations and turrets, repeated the “land” version of the DK with all its shortcomings, the main of which was an absolutely insufficient rate of fire for aviation, only 300 rounds/min, and a decent weight of 35.5 kg.

In 1934, the production of DC was suspended, and in 1935 it was discontinued. To a large extent, B.G. contributed to stopping work on improving the Degtyarev heavy machine gun. Shpitalny, who promised I.V. Stalin received a machine gun with the best characteristics based on the aviation ShKAS - the 12.7 mm ShVAK machine gun. However, the fate of the 12.7 mm ShVAK did not work out. Partly due to the complexity of the design inherited from ShKAS, partly due to the impossibility of using a standard 12.7x108 cartridge in the ShVAK automatics. As a result, in parallel with the Degtyarev cartridge, a ballistically identical cartridge for ShVAK 12.7x108R with a protruding rim was put into production. Apparently, “at the top” they still considered it inappropriate to produce two types of cartridges in parallel, giving preference to the more universal and automatic-friendly cartridgeless cartridge, and the production of 12.7-mm ShVAKs was curtailed in 1936 in favor of the 20-mm air cannon.

Meanwhile, the need for a universal heavy machine gun was still very urgent. Fortunately, V.A. Degtyarev managed to bring his brainchild to acceptable characteristics in 1935 - 1936. To increase the survivability of parts and the rate of fire, a spring buffer of the bolt frame was introduced into the machine gun, which increased the roll-up speed of the moving system, which required the introduction of an anti-rebound device to prevent the frame from rebounding after an impact in the extreme forward position. Working out the machine gun's power supply system remained a serious problem. In 1937, Georgy Shpagin significantly improved his version of the tape receiver, creating a drum mechanism for feeding a metal one-piece tape in sections of 50 cartridges of the original design. In April 1938, the belt-fed machine gun was successfully tested, and on December 17 it passed field tests. And on February 26, 1939, the model was put into service under the designation “12.7-mm heavy machine gun model 1938 DShK (Degtyareva - Shpagina large-caliber).” The machine gun was considered as a means of combating air targets, light armored vehicles, as well as manpower and enemy firing points in shelters.The machine gun began to enter the army in 1940.

In the same 1938, based on the “land” DShK, the aviation TsKB-2-3835 was developed in versions of the wing DShKA and synchronous-wing DNA with belt power, as well as the turret DShTA (DSHAT) for a 30-round Kladov drum magazine. Work on aviation versions in addition to V.A. itself. Degtyarev and G.S. Shpagin was led by K.F. Vasiliev, G.F. Kubynov, S.S. Bryntsev, S.A. Smirnov. Structurally identical to each other, the aircraft machine guns were made with high degree unification with the DShK machine gun. The difference was a higher rate of fire - 750-800 rounds/min, which was achieved by using loose metal tape with a smaller pitch between links - 34 mm instead of 39 mm for the one-piece DShK belt. It is characteristic that Degtyarev also hedged his bets by developing versions both for the standard 12.7x108 cartridge and for the ShVAK welted 12.7x108R cartridge.

Unlike the DShK machine gun, its aviation versions had the ability to quickly change the barrel. The feed of the tape on the wing-mounted DShKA and synchronous DNA versions of the machine gun was carried out on the left side, although in production versions it would certainly have been possible to change the direction of feed of the tape. By the end of 1938, the DNA synchronized machine gun, and apparently this version was given the highest priority, successfully passed field tests, with virtually no comments. But here's the fate of this interesting weapons chance intervened. Just in the fall of 1938, the UB aviation machine gun, a young and practically unknown designer M.E., passed a series of factory and field tests. Berezina, showing exclusively high performance, good survivability and reliability of its automation. Using the same loose belt of DK cartridges, it fired faster, was lighter and technologically simpler. There is a legend that at the beginning of 1939, at a meeting with Stalin, where promising types of weapons were considered, the question of a new aviation heavy machine gun was raised. Stalin, puffing on his pipe, looking into the eyes of V.A. Degtyarev, asked: “So which machine gun is better, yours or comrade Berezin’s?” To which Degtyarev, without hesitation, replied that “Comrade Berezin’s machine gun is better.”

The result is known. Our aviation received, perhaps, the best aircraft machine gun in its class in the world. Well, Degtyarev got the “land” niche. The large-caliber DShK in various modifications was in service in the USSR for many decades, and after its collapse in the armed forces again formed states. And even now it is often found all over the world.

The DShK was used by the USSR from the very beginning of World War II in all directions and survived the entire war. It was used as an infantry weapon, from various machines, and was placed en masse on trucks for air defense. The DShK was the main armament of the T-40 (amphibious tank), LB-62 and BA-64D (light armored vehicles), and experimental ZSU T-60, T-70, T-90. In 1944, a 12.7-mm anti-aircraft turret with a DShK was installed on the IS-2 heavy tank, and later on heavy self-propelled guns for self-defense of vehicles in the event of attacks from the air and from the upper floors in urban battles. Anti-aircraft armored trains were armed with DShK machine guns on tripods or stands (during the war, up to 200 armored trains operated in the air defense forces). A DShK with a shield and a folded machine could be dropped to partisans or landing forces in a UPD-MM parachute bag.

The fleet began receiving DShKs in 1940 (at the beginning of the Second World War there were 830 of them). During the war, industry transferred 4,018 DShKs to the fleet, and another 1,146 were transferred from the army. In the navy, anti-aircraft DShKs were installed on all types of ships, including mobilized fishing and transport ships. They were used on twin single pedestals, turrets, and turrets. The pedestal, rack-mount and turret (coaxial) installations for DShK machine guns, adopted by the Navy, were developed by I.S. Leshchinsky, designer of plant No. 2. The pedestal installation allowed for all-round firing, vertical guidance angles ranged from -34 to +85 degrees. In 1939 A.I. Ivashutich, another Kovrov designer, developed a twin pedestal installation, and the later appeared DShKM-2 gave all-round fire. Vertical guidance angles ranged from -10 to +85 degrees. In 1945, the 2M-1 twin deck-mounted installation, which had a ring sight, was put into service. The DShKM-2B twin turret installation, created at TsKB-19 in 1943, and the ShB-K sight made it possible to conduct all-round fire at vertical guidance angles from -10 to +82 degrees.

In 1945-46, the troops were armed with the already modernized DShKM. As an anti-aircraft DShKM machine gun installed on tanks T-10, T-54, T-55, T-62 and other combat vehicles. And in the IS-4M and T-10 tanks it was paired with the main gun. In the version for installation on armored vehicles, the machine gun is called DShKMT or briefly DShKT. After the end of World War II, the DShK machine gun was used in almost all local conflicts.

Unofficial, affectionate nicknames among the troops are “Dushka”, “Dashka”, “Tar”.
Work was carried out on the DShK aircraft installation, but it soon became clear that the Berezin system (UB) machine gun was better suited for aviation use due to some characteristics.
The German army did not have a standard heavy machine gun, so they gladly used captured DShKs, which were designated MG.286(r).