DIY children's slippers. DIY children's slippers made of fur

In winter, returning home after a walk along the frosty streets, you really want to put your feet in something soft and warm! Are cozy winter slippers already waiting for you at the door? If not, don't rush to the store. You might be able to make them yourself!

House slippers made from an old sweater

A zealous housewife has none old thing doesn't go to waste. Especially, such a multifunctional item as a worn sweater, from which, among other things, you can sew cute slippers-boots.

To work you will need:

• Basic cutting and sewing tools
• Sheet of cardboard and pencil
• Double-sided tape (optional)
• An old sweater (it is advisable that the fabric does not fray too much when cutting)

Place your foot on the cardboard and trace its outline with a pencil. Add 1.5 cm along the perimeter of the outline to the seams and cut out the patterns. Do the same with the other foot. When both pieces are ready, place them on the sweater and cut out similar pieces of fabric. To prevent the cardboard from slipping while working with the material, it can be secured with double-sided tape.

Now measure the length of the top of your future boots. To do this, insert your leg into the sleeve of the sweater and pull it to the required height, then carefully cut the sleeve off near the floor. Do the same with the other leg.

Next, fasten the fabric foot with the corresponding sleeve boot using sewing pins. First, connect the blanks where the big toe should be, then at the heel, and then stretch the bottom of the boot as far as necessary to pin together the sides of the slippers. Sew as shown in the photo below:

Master class No. 2

From the same sweater and a piece of felt you can make more familiar, “classic” slippers.

Exactly as in the previous case, outline and cut out patterns for the feet from cardboard. Then transfer them to felt and cut out 2 blanks for each leg - one of them will become the sole, and the second will become the insole.

Next, place the patterns on the sweater, stepping back from its bottom edge by about 3 cm, and outline them as shown in the photo. The distance between the line and the top point of the insole (where the big toe will be) should be about 2 cm (more on the sides). Do the same manipulations with the remaining patterns.

Glue the felt blanks to the front and back sides using double-sided tape.

Try to keep the edges of the felt insoles as close as possible.

Stitch or stitch in the round, placing right side up.

Now you need to sew the upper part of the slipper (the one that covers the top of the foot). Measure approximately 12 cm of the sleeve, starting from the cuff, and cut it off. Sew up the cuff and round the opposite side of the piece so that it is shaped like half an egg.

Make another similar blank. You should end up with two pieces of fabric with felt insoles sewn on both sides and two “caps”. This is where the preparation ends and you can start stitching the fragments together.

Place the cap on the front side with the sewn insoles. Its top should coincide with the center of the rounded side. Sew them together at this point.

Then slide the cap down 2.5 cm and sew the corners of the cap and the sides of the fabric with the insoles together. Make a couple more stitches halfway from the top of the cap to the corners.

Turn the resulting structure inside out so that all the seams remain inside the sneaker, and make two cuts on both sides of the heel. The cuts should end a few millimeters from the felt insole.

Now form the heel from two side flaps, carefully straightening the central one from the inside. Make two vertical stitches about an inch apart to secure the side pieces of the heel, and then another along the insole. Repeat the same with the second slipper.

And finally, the final touch is the lapels.

Trim the bottom edge of the sweater in a circular pattern. Fold the raw edge under so that the ribbon is approximately 5cm wide. Then cut it in half, preferably along the side seam lines. Secure a few pieces of double-sided tape to each half.

Wrap the strip around the edge of the sneaker and secure with a couple of stitches so that it does not slip or dangle. Accordingly, fasten the second strip to the second sneaker. Ready!

Felt slippers

Using a similar set of tools, you can sew slippers only from felt. Moreover, you will not have to process the seams, since this material does not fray when cut, which means the work will take even less time than in the case of a sweater.

So, stock up on a piece of colorful felt, some laces, and some basic sewing supplies.

First, cut out the insole from cardboard, as described above. Don't forget to allow seam allowance (approximately 1 cm). After this, place the insole on the felt, outline and cut out the workpiece according to the following pattern:

• Distance from the top of the insole (i.e. thumb) to the edge of the fabric – 2.5 cm
• The distance from the sides of the upper part of the insole to the edges is 3.5 cm
• The distance from the insole to the sides of the rectangle is about 8 cm
• The distance from the bottom point of the insole (i.e. the heel) to the edge of the fabric is 1.5 cm

Remember, it's better to leave a little extra material that can be removed later than to cut it off end-to-end and ruin everything!

Proceeding in this way, make two identical blanks.

1. Fold the piece in half, staple and stitch the two halves along the heel and curved part of the toe.
2. Now you need to round the heel. Without turning the slippers right side out, press and stitch the right angle between the foot and the heel (see photos 3 and 4).
3. Turn right side out and fold back the top of the boot. (see photos 5 and 6)
4. Fold the very tip of the sneaker up so that the corner coincides with the middle seam, and secure it with an X-shaped stitch.

To thread decorative laces into the boot, make a few marks with chalk or a disappearing tailor's marker, about 1 cm from the top edge of the lapel. Then pierce the cuffs along with the boot, following your marks, and thread the laces through them. Large wooden or plastic beads can be attached to the ends of the laces to give the entire structure a finished look.

Your slippers are ready!

DIY bunny slippers

Bunny slippers are a classic, but do they all have to look the same? Why not take a common model as a basis, but make something of your own as a result?

For example, here are these cute house boots with applique:

During the work you will need:

• Old wool sweater
• Patterns ( ready-made samples )
• White and pink felt
• Thick, non-slip fabric for hemming sneakers at the bottom
• Thread, needle and other basic sewing supplies

At the link above you will find samples of patterns for cutting out applique details. They can be proportionally increased or decreased if necessary, just do not forget to leave seam allowances (approximately 1 cm on all sides of the part).

The sweater must first be washed in hot water, and then dry it in the dryer (or straight in the washing machine) until it shrinks and feels as much as possible. If after drying you still see loops under the pile, repeat the entire procedure again.

Step-by-step instruction

Place the slipper patterns on the pre-smoothed fabric and cut out the parts for each leg one by one (there should be 4 of them in total, since each slipper will be sewn from two halves).

Then cut out the bunny's tail from white felt. Place one half of the slipper face up on the table and place the tail on top of it, as shown in the photo:

Place the other half of the slipper on top, face down.

Secure the back and top of the slipper with sewing pins and stitch. Let the bottom edge remain unstitched for now.

Do the same with the second slipper.

Then cut out the hare's face and ears from felt (the outer side is white, the inner side is pink).

Sew the ears by placing the pink piece on top of the white piece, both right sides facing up, and making just one stitch down the middle. The unstitched edges of the pink felt will puff up slightly, but general form applications only benefit from this.

Then fold the bases of the ears along the line of the central seam and intercept them with thread - when you attach them to the slippers, the density of the folded fabric will not allow the parts to sag. A total of 4 ears are needed (2 for each application).

Now cut out the pink nose and sew it to the muzzle along the edge. Instead of eyes, you can sew two black buttons, embroider them with satin stitch or draw them.

You will need 2 of these muzzles - one for each slipper.

Turn the prepared top part inside out and sew the muzzles and ears to it as follows:

As you can see, the ears are inserted under the hare's muzzle, and are sewn with the same line as it. Sew around the entire perimeter of the applique to make it easier for you to sew on the bottom. You should end up with something like this for each slipper:

Turn it inside out and set it aside for now. You have already done the lion's share of the work, all that remains is to cut out and sew on the sole.

To do this, first cut out two insoles from the sweater. There is only one pattern for them, you just need to turn it over so that the curve matches the curve of the foot, i.e. was facing right or left.

Then do the same using the thick fabric you chose for the sole. Place the insoles and soles in pairs. The insole should lie with the front side up, the sole - vice versa. Sew the folded parts around the perimeter, stitching almost along the very edge.

All that remains is to sew the upper part of the slippers and the soles.

Pin the center heel side of the sole to the heel seam of the sneaker, then do the same with the toe and front of the sole. To find the center, simply fold the sole in half lengthwise so that the side edges match each other.

It is better to insert pins from the top, this will make it easier for you to sew the parts together.

As a result, the slipper should look something like this (remember that you are working from the inside out, and the applique remains on the inside):

Sew it around the perimeter of the sole.

The edges can be overlocked to make them look neater.

Having done this procedure with both slippers, you can turn them right side out and straighten the seams.

To make cuffs, cut off the bottom edge of the sweater (“elastic band”) and press it along the side seams. Then fold each half in half and sew the edges together to create a ring. That's all, all that remains is to sew these rings to the tops of the sneakers, with inside and then turn it out.

If you did everything correctly, congratulations, you have become the owner of a pair of these fun cute slippers!

Shoes can tell a lot about a person. About how neat you are, whether you follow fashion. Your shoes, sandals, and boots can tell you whether you suffer from diseases of the joints of your legs. But if the shoes that we wear to go outside or go to work must meet some standards, then you can choose any house slippers depending on your desires.

We always associate slippers with coziness and comfort. After all, these are comfortable and sometimes warm indoor shoes, in which it is easy and pleasant to walk around the house.

Today, stores offer a wide selection of shoes for the house, both warm and regular, for the hot season. These can be slippers and flip-flops, closed and open, from a variety of materials.

If you wish, you can purchase special shoes with orthopedic insoles so that your feet can rest in them after a hard day. Orthopedic shoes for home can be suitable for people suffering from various types of foot diseases - gout, varicose veins, flat feet.

But you can also make home slippers yourself. This option is especially suitable for those who love handicrafts. You can make many pairs of slippers for each family member and guests. The slippers can be different, or they can be made in the same style. There are many options, the main thing here is to give your imagination the opportunity to run wild. Homemade slippers can also serve as a gift for a family member or close friend.

In this case, you can sew them according to an individual sketch. This is very convenient, because house shoes, which are sold in stores, are sewn according to standard patterns. For people who have wide or, on the contrary, narrow feet, it is simply not suitable.

So, how to sew slippers yourself?

In order to sew home slippers you will need durable soft material. The material can be old items made of thick knitwear, drape, leather, jeans or fur. Before you start sewing, decide on the model and color, sketch out a sketch and make a pattern. It is very easy to make a pattern based on the shape and size of the foot by placing the foot on a piece of paper and tracing it. For example, if you decide to make homemade slippers from felt, then making them may only take you half an hour.

To begin, make a pattern as described above, simply trace your foot by placing your foot on a piece of paper. Then, to the resulting drawn foot, draw two rectangles on the right and left, which will serve as a jumper holding the slipper on the foot. Once the pattern is ready, cut it out and place it on a piece of felt. It is enough to make a pattern for one foot, for example, the right one, its reverse part will serve as a pattern for the left foot.

Trace the pattern placed on a piece of felt with a pen and cut it out. Then connect the side parts of the jumper with each other into a ring, and try on the future slipper on your foot. Fix the jumper by adjusting it to the leg and sew. So you have a slipper. You can decorate it as your heart desires. Any decoration is suitable here: buttons, rhinestones, beads, fur.

You can also make fabric slippers at home. In order not to fantasize with the pattern, you can tear up old slippers that have served their purpose and make a pattern in their likeness. If there are no old slippers in the house, then make a pattern yourself, also tracing your foot placed on a sheet of paper. It is better to use dense material as the sole of house slippers. This can be several layers of thick fabric, leatherette, thick denim. After all, the main load falls on the sole, and if it is too thin, it will quickly fray and wear out. And walking in slippers with thin soles will not be very comfortable.

You can make the sole of the slippers from thick material and crochet the top. Thus, you get original slippers that no one else has. That is, you can easily become the author of a real designer model!

Slippers - moccasins

The Indians made similar slippers and shoes for themselves and called them moccasins.

Slippers are made of felt or leather.

You can use two old felt hats as felt. Soak the hats in water overnight. When the felt softens, straighten it and stretch it well (do not overdo it, so as not to tear it), laying it out on a flat surface. After it has dried, cut out patterns for the right and left legs (Fig. a) according to the foot size you need. The side stripes of the slippers, for which in Fig. “a” indicates a width of 60 mm; a children’s slipper will have 40 mm.

First make a pattern out of paper, check all the dimensions again and redraw it onto felt or leather. Don't forget to cut out the tongue (Fig. b). Using a punch, punch holes in both slippers and tongues as shown in Fig. "a" and "b". Cover them with thin strips of leather or felt of a different color (Fig. c). Sew the heel first, then the toe. When sewing a sock, sew in the tongue. It can be decorated with a drawing or embroidery (drawings with acrylic or special paints on leather - on leather slippers, embroidery - on felt ones) (Fig. d).

At any time of the year, shoes such as slippers are relevant. In summer, your feet get a rest from sandals, and in winter they keep you from freezing. We suggest you make one attached to each master class.

Preparing the pattern

Whatever kind of slippers you sew, to simplify the sewing process, at the first stage you need to make a foot pattern.

Operating procedure:

1. Take cardboard, marker and scissors.
2. Place a piece of cardboard on the floor and place your foot on top.
3. Trace the outline of the foot with a marker. Do not press the felt-tip pen close to your foot.
4. Carefully cut out the trace along the outline.

The pattern is ready. Now you can apply this mark to any fabric and sew slippers. If you need to sew slippers of a different size, simply reduce or increase the pattern.

One Piece Closed Toe Slippers

The one-piece pattern is very easy to make. To build it, you will need to take a marker and a suitable dense fabric (for example, felt or fleece).

Master Class:

1. Place the pattern on the selected material and trace it. Complete the elements as in the illustration above.
2. Cut out the part along the contour.
3. Fold the piece and sew along the edge.
4. Carefully turn the slippers inside out.
5. Make another slipper in the same way.

You can add a lining if you wish. To do this, make a pair of slippers from thin fabric in the same way and sew the two parts together.

Slippers from an old sweater

You can make your own slippers from an old sweater. Patterns are not needed for them, you just need to have a foot template.

Sewing master class:

1. Take an old sweater and cut off the sleeves.
2. Fold the sweater and attach the pattern to it.
3. Trace the pattern and cut out the soles of future slippers. A total of four such parts are needed.
4. Baste two parts of the sole together. This will make the slippers thicker.
5. Sew one sleeve and one sole together. This can be done with thick threads and interesting stitches. This will give you a decorative stitch. Or you can use simple stitches, then the slippers will need to be turned inside out.
6. Topstitch or hem the top of each slipper to prevent the threads from fraying.

Sweater slippers are ready!

Children's slippers

Of course, you can make the same slippers for a child as for an adult, just smaller in size. But it’s much better to make interesting and unusual children’s slippers with your own hands. Make patterns based on the child’s feet.

Master class on creating children's slippers:

1. Cut three pairs of soles: two from fleece or felt, and one from a softer material.
2. Cut out one pair of slipper tops. It should be slightly wider than the sole so that the slipper can be easily put on the foot.
3. Additionally, cut out two pairs of ears and one pair of noses.
4. Cut out the letters “P” and “L” so that the child can distinguish the right sneaker from the left.
5. Sew all three insoles together. The soft part should be in the middle.
6. Sew a nose to each top of the slippers in the center, embroider eyes on the sides of it or glue buttons, and make a mouth.
7. Fold the ears in half and also sew them to the top part of the slippers, stepping back a little from the edge.
8. Sew the top piece and sole together.
9. Sew the letter “L” to one insole, and “P” to the other.

Children's slippers are ready!

Felt slippers

Felt slippers are very comfortable and warm indoor shoes, which are ideal in the cold season.

Making your own slipper pattern (Illustration 1) is done as follows:

1. Trace your leg on a piece of paper or use a pre-prepared pattern.
2. Draw one rectangle. This part is the sneaker cuff. Therefore, the size of the rectangle depends on the characteristics of your foot: the length should be enough for the slipper to be easily put on and not slip off, and the width is at your discretion.
3. Draw a detail that resembles half a sock. It should be slightly longer than the sole of the sneaker.

When the pattern for hand-made slippers is ready, you can start sewing shoes.

1. Take a thick fabric (such as felt) and fold it in half.
2. Take any piece of fabric (for example, an old sweater) and also fold it in two layers.
3. Attach the pattern to the fabric and trace it with a marker or chalk.
4. Cut out the pieces. In total you should have the following number of elements: two soles, two cuffs and four “socks”.
5. Connect one sole and two “socks” with needles and pins.
6. Topstitch or sew the pieces.
7. Sew the cuffs to the top of the slipper.
8. Turn the finished sneaker inside out.
9. Sew the second felt boot in the same way.

Felt slippers are ready!

Ballet slippers

You will need to take the following materials to make these home slippers with your own hands:

1. Pattern of the sole (foot pattern) and sides.
2. Soft fabric (such as flannel or flannel).
3. Batting or other similar fabric for filling.
4. Felt or any other fabric for the sole (you can buy special non-slip fabric at a sewing store).
5. Rubber.
6. Thread, needle, scissors, marker.

Master class on how to improve your slippers:

1. A pattern for slippers (made with your own hands) of this type consists of two parts: the sole and the side. Print the finished layout on paper or draw your own.
2. Using the sole pattern, cut out two parts each from the insole, filler and sole (Illustration 1).
3. Cut out two pieces for the top of the slipper. To do this, fold the fabric in half with the right side facing inward. Attach the pattern to the fold line and trace the outline. You need two such parts (Illustration 1).
4. Carefully fold the two layers of sole and attach the upper part to them with needles and pins, as in illustration 2.
5. Sew up the details.
6. Similarly, make a lining for the slipper from soft fabric (Illustration 3).
7. Sew two pieces together. The seam should go in two rows (Illustration 4). This is necessary so that you can insert the elastic later. So leave a small hole at the back.
8. Turn the sneaker inside out and insert the elastic band.
9. Sew up the hole.

House slippers are ready! You can decorate your socks with decorative pompoms, roses or beads.

House slippers should be comfortable, light and soft so that your feet can rest after a hard day at work.

Today, various styles of slippers never cease to delight our female eye. We cannot pass by the beautiful house shoes, which are embroidered with crystal stones, decorated with sequins and rhinestones. Winter versions of slippers fascinate us even more: boots with ears or warm flip-flops with fur. In this article we will tell you how to sew slippers using a pattern.

House shoe models

Today in store windows we can see a huge assortment of house shoes. Modern designers annually update their range of slippers with new types and interesting colors.

House slippers are not a cheap pleasure, so many women are interested in how to make a pattern for house slippers with their own hands and sew shoes using it. But for this you need to decide on the style of the product.

House shoes can be divided into several types:

• flip-flops;
• closed-toe slippers;
• indoor boots;
• 3D house shoes;
• UGG slippers;
• moccasins;
• slippers-socks.

To understand how to make a pattern for house slippers, boots or Ugg boots, closed-toe slippers or indoor slippers, you need to take a few tips:

1. To avoid taking measurements, you can take an old slipper, put it on paper and outline the sole.
2. In order to sew on the edging you will need an awl.
3. As a rule, the sole is cut out of leatherette, split leather or leather.
4. The insole can be cut from cloth or suede.
5. To sew a high-quality and durable product, you need to purchase special nylon threads.

Material for sewing house shoes

To make a pattern for house slippers with your own hands, you need to select a fabric and stock up on everything you need. Material for sewing house shoes should be of high quality and light, for example:

• fleece;
• mahra;
• jeans;
• wool;
• plush;
• suede leather;
• felt.

You can cut out and sew light house slippers or moccasins from denim, felt and suede. Beautiful products made from fleece, terry and plush. From these types of fabric you can sew any model of house shoes.

How to sew home slippers: felt pattern

To create these house shoes you will need to make a complex pattern. You will need the following materials:

• 0.5 m felt;
• scissors;
• gypsy needle;
• glue from a gun;
• bright floss threads;
• bullseye patch;
• cardboard;
• pencil.

The DIY slipper pattern will look like this:

Manufacturing process:

1. Take a piece of cardboard and place your feet on it, using a pencil to outline your left and right feet.
2. Now cut out the soles with scissors and trace them on the fabric.
3. Cut out these elements.
4. Next we need to create the upper of the shoe. To do this, we again take cardboard and draw two semicircles. The sizes of these parts depend on the fullness and length of your foot.
5. After that, we transfer these two parts to felt and cut them out.
6. You should end up with four patterns.
7. We must sew the upper part of the slipper with the sole.
8. This can be done using floss threads.
9. Once the two elements are sewn together, we can move on to decoration.
10. We must sew a colorful patch to the top of the product.
11. Now, using the same pattern, we sew and decorate the second slipper.
12. Felt house shoes with bright stripes are ready!

How to sew Ugg slippers

Fleece slippers are ideal for sewing such a product; they will be warm, soft and will last you for many years. To create a pattern for home slippers, you will need 1 m of fleece, 0.5 m of suede and 0.5 m of leather. It would be good if these materials were matched to match. You also need the following sewing supplies:

• threads to match the fabric;
• needle;
• scissors;
• glue "Moment";
• centimeter;
• ruler;
• cardboard;
• pencil;
• pins.

Pattern of Ugg slippers:

1. Cut out 38x20 cm rectangles from cardboard for the boot (two parts).
2. We pin the patterns to the fleece, trace and cut out with a 1 cm allowance.
3. We cut out suede insoles 23 cm long.
4. Now we take the leather and cut out the soles approximately 24 cm in length.
5. Using pins, we chop off the upper parts of the boot face to face.
6. Trim the seam allowances, fold the back edges of the boot and grind them down, leaving a hole in the lining through which you will turn the product inside out.
7. Sew the top of the boot from the foot to the top vertically.
8. To ensure that the boots do not dangle and sit beautifully on the foot, we move on to the darts. Make four notches in the places where the product bends (in the area of ​​the boot) and carefully sew them together, trim off the excess.
9. Now turn the outer part of the sneaker right side out, insert a suede insole into it and sew up the hole with a hidden seam.
10. Carefully coat the leather sole with glue and connect it with pins to the foot of the product.
11. We do the same with the second boot.
12. When all the work is ready, take the boots and fold the top of the products.
13. You can embroider these lapels or decorate your ugg boots with ribbons.

How to sew homemade slippers and socks yourself

Making a pattern for house slippers with your own hands is quite labor-intensive and meticulous work. To simplify the task, you can use beautiful terry socks. Thus, you can create original house shoes in just 10 minutes!

For this you will need:

• red terry socks;
• leatherette - 0.5 m;
• glue "Moment" (or glue from a gun);
• decoration (bows, beads and stars);
• scissors;
• needle;
• marker;
• red threads.

Step-by-step guide on how to make slipper socks:

1. The sole should be made from leatherette. To do this, place your feet on the material and use a marker to outline the outline of your feet.
2. Using scissors, cut out the soles and glue them to the socks.
3. After the slippers have dried, you can proceed to decorating.
4. Make a lapel on the product blank.
5. Take a slipper and decorate the side (outside) with a striped bow, right on the lapel.
6. Sew beads a little lower and attach a couple of metal stars.
7. The second slipper should also be decorated in this way.

Using this pattern, you can sew similar house shoes, but come up with other ways to decorate. It all depends on your taste and ideas!

Original slippers: how are shoes decorated?

The fashion trend in 2017 was chic fur slippers and flip-flops with fur. The pattern of home slippers made of fur is simple: to do this, you can take an old fur coat from a fox (nutria or rabbit) and cut out four parts according to your measurements - two semicircle tops and two insoles (the process has already been described).

Then we carefully sew the upper parts of the shoes with the lower elements using special nylon threads. We cut out the soles of old slippers from leatherette and glue them to the insoles.

If you want to surprise your guests, you can decorate your slippers in an original way. Here everything will depend on your imagination. You should start from the general color scheme of the slippers; you don’t need to glue on them a large number of variety of decorations. Everything must be done with taste. For example, after you have made a pattern for house slippers, decorate the product with bows. Attach decorations to the sides of the outside of the boots. So, what else can you decorate your slippers with?

Elements for decorating house shoes:

• ribbons;
• stars;
• zigzag braid;
• floss threads;
• buttons;
• stones;
• embroidery;
• rhinestones.

In order for the decorations to sit firmly on the product and not fall off after the first wash, they should be set with glue or sewn tightly with threads.